Weatherby model 82 Illustrated P

Weatherby model 82
Parts List

These illustrations were scanned off from Weatherby factory catalogs, and ARE factory ID and part numbers. This is important as about all obsolete parts suppliers use ONLY factory or closely associated numbers where ever possible so everyone is on the same page.

We thank Weatherby for supplying the above scanned picture

Weatherby Model 82 parts listing

The parts listed below are for your identification purposes only.
The author of this website DOES NOT have any parts.

ID	Part #	Nomenclature	ID	Part #	Nomenclature
1	3340	Magazine Cap	46	3311	Retaining Screw
6	4228	Barrel Assembly	47	3312	Safety Spring
7	3071	Bead - Barrel	48	3313	Safety Plunger
8	3262	Piston - Gas	49	3314	Safety Button
9	3245	Operating Handle	50	3368	Frame- Trigger
10	3342	Bolt Body	51	3232	Spring - Sear
11	605	Pin - Retaining, FP	52	3233	Sear
12	3261.NS	Firing Pin	53	3369	Sear Pin
13	3308.NS	Firing Pin Spring	54	3322	Spring - Detent
14	3345	Extractor	55	3321	Tube -Rear Trigger Frame
15	3346.NS	Plunger - Extractor	56	3215	Pin - Action Tube Plug
16	3347.NS	Spring - Extractor	57	3216	Plug - Action Tube
17	X3349	Locking Block	58	3217	Follower - Action Tube
18	604	Pin - Plunger Retaining	59	3218	Spring - Action Tube
19	3260	Operating Handle Plunger	60	3219	Tube - Action
20	3259	Operating Handle Spring	61	3315	Extension - Magazine
21	609	Carrier Extension Pin	62	3316	Retainer -Extension
22	3284.TPA	Carrier (conversion)	63	3213	Spring - Magazine
23R	3351	Carrier Extension RH	64	3323	Plug - Magazine
23L	3352	Carrier Extension LH	65	3370	Follower - Magazine
24	4245	Slide Assembly	66	3214	Magazine Tube
24	4208	Slide Assembly (conversion)	67	3324	Retainer - Latch Pin
24a	3353	Slide Tube Key	68	3206	Latch Pin
24b	3354	Slide Bar	69	3208	Spring - Latch
24c	3355	Slide Tube	70	3208A	Spring - Blocker
25	3220	Trigger Guard Frame Pin-Front	71	3371	Latch - Feed
26	3310	Trigger Guard Frame Pin-Rear	72	3272	Button - Bolt Release
27	614	Ring - Retaining, Lifter Pivot	73	4253	Blocker Assembly
28	3246	Pivot - Lifter	74	3202	Retainer - Ejector
29	3247	Pin - Lifter Dog	75	3205	Ejector
30	3259	Lifter	76	3203	Spring - Ejector
31	3248	Lifter Dog	77	3374	Receiver Insert
32	3361	Follower - Lifter	78	3375	Receiver
33	3362	Spring - Dog Follower	79	601	Recoil Pad Screw
34	3236	Spring - Detent	80	3204	Recoil Pad
35	3237	Pivot Tube - Hammer	81	3200	Nut - Action Tube
37	3363	Hammer	82	602	Action Tube Lock Washer
38	3235	Plunger - Hammer	83	3275	Buttstock Washer
39	3364	Spring - Hammer Plunger	84	4220	Buttstock - Sub-Assembly
40	3225	Pin - Trigger	85	3356	Protecting Cover Screw
41	611	Pin - Disconnector	86	3357	Lock Washer
42	3366	Disconnector	87	3358	Protecting Cover
44	3229	Trigger Spring	88	3225	Disconnector Link Pin
45	3367	Trigger	89	3365	Disconnector Link

The Centurion II model used a different Slide Assembly, being quite similar to this 82, which the tube was solidly attached to the bars, both we can not easily duplicate. The rear attachment to the carriers are different, with the rear bars being connected at the rear, therefore requiring a different carrier than the Centurion. However we have come up with a Conversion Carrier that will allow you to retro-fit our Centurion Slide Assembly into the model Centurion II & the model 82s.

In the above listings the numbers in BLACK represent the parts that are different than the Centurions.

Back to the Main Ramblings Page

Originated 11-17-05 Last updated 11-08-2020
Contact the author